If someone knows if I did something wrong or if I can fix this some otherway I would be really glad. I guess easiest thing would be to temporarely put up my old Lyra mesh as they were, but had some connection issues lately, so this will need to wait until the weekend. Qfinder Pro automatically searches and displays all QNAP devices on the same network. I can turn it on and off with the power button and network connection lights are on. The utility supports Windows, macOS, Linux. First, I think you need to find the IP address of the NAS. The QTS login screen opens in the default web browser. Locate the NAS in the list, and then double-click the name or IP address. I hope the raid drives are OK and of course my NAS as well. Qfinder Pro is a desktop utility that enables you to locate and access QNAP NAS devices on a specific network. Qfinder Pro automatically searches for all QNAP NAS devices on the network. I guess I have two (or three problems), but first of all I need to somehow access my NAS and then I assume I need to change the IP, right? Or could it be the Asus firewall (settings), even though the Lyras has a similar firewall? At one point Qfinder anctually listed it with the old IP as I was changing, but couldn't connect. I also have an ethernet swith, to which I earlier connected my NAS, but now I tried both router and switch back and fourth. I even tried to set the MAC-address of my NAS to a specific IP truogh my router, but this didn't work either. I had a similar problem with a Asus router (ax55 supporting aiMesh) earlier, but decided to return it, as I couldn't access my NAS and didn't have any interest to start digging in to the issue back then. ![]() I connected the lan cable, which I usually have connected to my mesh, to the NAS and changed my Ethernet-settings in Win 11 to static IP (IPv4): 169.254.100.99 and submask: 255.255.0.0 and opened Qfinder Pro, but it couldn't find it. I however checked how to connect directly with my PC to my NAS, but this didn't work. Check if the Status LED (same as the Power LED for some models). I have my old Lyras still, so I might go back to them if needed. Qnapfinder Cannot Find My NAS Check your LAN cable connection and the LAN LED is flashing. Now it's turned steady red.Īnyhow after changing from a Asus Lyra mesh to an Asus ZenWiFi XT8 mesh I haven't been able to access it. How to connect to a nearby QNAP NAS if I dont know the IP address Last modified date:. If it doesnt work, pls contact your distributor or our technical support asap. There was a notification, that said something about the raid rebuild and I found a topic on solving it, but I haven't tried it yet. You may replace the network cable and try again. I hope you know what I am about to write, because that would make this sooo easy. So, I install the Qfinder program, launch it and it locates my unit. The rebuild finnished and I could access my TS-351 NAS fine. At this point I wonder to myself, where is the desktop dashboard I need to operate this NAS I Google some more and it seems as if it is the Qfinder program. Anyhow I also swapped out a raid-disk and did a rebuild. But, sadly, it disappears after a few seconds.Īny help in diagnosing what my problem might be would be greatly appreciated.Hi, I have a problem and I think it has to do with me changing my router, but I'm not sure. ![]() The NAS will also briefly appear in Qfinder if I unplug and replug the ethernet cable. verified that the workgroups are the same name ensured that the network discovery it turned on enabled local master browser on the NAS and done a restart of all devices with the NAS doing a full boot before any other devices. changing the settings in IPv4 WINS to enable the NetBIOS Enter the IP of the enclosure again on your PC. ![]() ![]() Follow the steps to initialize the drives, install QTS, and set up your account. (There’s also the Qfinder Pro you can download.) The QTS install wizard will load up. To enable this service, go to Control Panel > Network & File Services > Service Discovery and in the tab UPnP Discovery Service, you may enable the UPnP Discovery service to address this issue. Go to your PC and enter IP of the enclosure. Interestingly, if I restart the NAS while my computer is running, there is a ~30 second period where Qfinder (6.4.2) registers the NAS and I can even login to it, but it disappears from Qfinder after the long beep sounds. This issue could be caused, because UPnP discovery service is disabled. I am able to see the NAS via the apps on my phone and on my wife's Mac so I think there is a setting that is windows specific. Last week my TS-220 was working like normal, but for some reason a setting got changed somehow (around the time of a power outage if it could make a difference) and now I am unable to map the NAS after full boot-up on my Win10 V.1709 (OS Build 16299.309) machine.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |